Glen Pack

IMC. Install a booster ducted split heat pump system for the master suite and upper half of the existing condo.

Relocate 3 supply registers.

Relocate forced-air outlets and Wls7s in the master bath/dressing area; install hydronic radiant warming in the lower-level recreation room using existing boilers.

Install a ducted heat pump system for the cottage.

Install multi-head duct-style heat pumps/mods to existing systems; install exhaust fans/HRVs. 250 devices. 200-amp service.; new wiring, new devices, new appliances, new fixtures, new 200-amp service. Amendment (10/17/19): In addition to forced-air systems, install ground ductwork and radiant in the following areas: lower leve, great room, kitchen, mud room, loggia.

Replace gas furnace and 2 water heaters in the basement; replace condensing gas-fired furnace and air conditioning for the garden room; replace condensing gas-fired furnace and air conditioning for the second floor.

Install a high-efficiency condensing gas-fired boiler with an indirect water heater; 5 hydro air systems, including ducting, piping from the boiler to air handlers, and vent piping. ACCA Manual J.

Replace the first-floor evaporator coil and outdoor compressor with equally sized equipment.

Miscellaneous ductwork to accommodate interior alterations.

HVAC: Move 2 registers and venting 2 fans.

Furnish and install a 4-head ductless split system for 3 bedrooms, the second floor, and the top rear space of the house.

Relocate supply outlets for changing room.

Remove the existing evaporator coil, thermostat, and wall condensing unit, and install new equipment of equal capacity and configuration.

Remove existing oil-fired boiler and gas-fired water heater, and install a new high-efficiency condensing gas-fired boiler with an indirect water heater. Reconnect to existing heat and hot water piping, wiring, and gas piping.

Install 2 hydro-air systems (condensing units on the roof), one direct-vent gas boiler, 1 indirect water heater, radiant heat for the first floor, and floor warming for the garage and porch.

Air conditioning system for the second and third floors.

Remove existing 4-ton R-22 air conditioning equipment and replace it with new equipment. Remove the old equipment and tie into existing ductwork, piping, and wiring. Activate and test for proper operation.

Remove existing 2-ton heat pump equipment for the space over the garage and replace it with new equipment of equal capacity and higher efficiency.

Furnish and install a high-efficiency ductless split heat pump system for a studio.

Replace oil furnace and cooling system.

Furnish and install a heating and cooling system serving the kitchen, living room, and dining room. An additional heat pump unit will be installed to serve the office, spare bedroom, and bedroom for the residence.

Remove the second-floor bedroom system and replace it with a new Carrier Performance 16 condensing unit and fan coil.

Remove the second-floor bedroom system and replace it with a new Carrier condensing unit and fan coil.

Miscellaneous ductwork to accommodate interior alterations.

Remove the existing second-floor evaporator coil module and condensing unit and replace them with new equipment of equal capacity.

Miscellaneous ductwork; replace electric water heater.

Remove existing cooling equipment and replace it with new equipment of equal or higher efficiency and capacity.

Remove existing cooling system and furnace and replace with new.

Furnish and install heating and air conditioning modifications for the house. Includes a condenser and air handler.

Miscellaneous ductwork; install wine cellar unit, cond. Will be installed in the basement.

Miscellaneous ductwork, piping, and controls; install fans.

Replace the existing furnace and air conditioning with a high-efficiency furnace and condenser. Miscellaneous ductwork to accommodate interior alterations.

Install a ductless split heat pump for the sunroom.

Replace existing gas-fired boilers with new gas modulating boiler.

Miscellaneous ductwork to accommodate interior alterations.

Finish and install a gas-fired boiler for the house; install a snow melt system.

Replace existing oil-fired boilers and install a new high-efficiency gas-fired modulating boiler.

Heat and cool 2 main floors of living areas as illustrated on plans.

Install 2 in-line bath fans and 1 dryer booster fan connected to existing exterior locations.

Underground piping. Amendment (8/9/18): Install heating and air conditioning, including a gas boiler.

Miscellaneous. Installation of duct modifications and radiant heat piping.

Furnish and install heating, cooling, and ventilation.

Furnish and install heating and air conditioning.

Unit 6-I. Replace packaged cooling unit for house.

Replace hydro-air heating and cooling systems.

Furnish and install heating and air conditioning for the first and second floors of the house.

Heating and air conditioning enhancements.

Install heating, ventilation, and cooling for house.

Furnish and install heating and air conditioning for house.

Furnish and install HVAC modifications.

Ductwork modifications. Amendment (12/12/16): miscellaneous ductwork for kitchen.

Furnish and install a heating and air conditioning system.

Furnish and install heating and air conditioning system modifications for the house; proposal and heat loss are in file BB. Amendment (10/30/17): Install a heat pump system for rooms over the garage.

Natural gas boiler.

Replace the 3.5-ton cooling system for the residence with a 4-ton high-efficiency variable-speed system, including new zoning equipment and controls.

Duct modifications to existing HVAC systems.

Geothermal heating and cooling for house (work completed).